CEL-MAR ADA-13040MG Instrukcja Użytkownika

User manualADA-13040MGETHERNET to RS485/RS422 Converterwith MODBUS GATEWAY1io_ada-13040MG_en_v1.12ADA-13040MGCopyright © 2001-2014 CEL-MAR sp.j.

3.3. RS485/RS422 BUS CONNECTIONThe RS485/RS422 interface is available in the ADA-13040MG on screw terminal block, labelled as: Tx+/A, Tx-/B, Rx+, Rx-.

Fig. 11. Example connection of the RS485(2W) devices to ADA-13040MG3.3.4. LINE TERMINATION Rt of RS485 BUSThe application of Line Termination (termina

5.2. INITIAL CONFIGURATION USING ADAFINDER SOFTWARE5.2.1. ADAFINDER INSTALLATIONThe initial configuration of network setting at the converter can be m

Fig. 13. ADAFinder configuration of IP network address5.3. CONFIGURATION AND MANAGEMENT BY THE USE OF INTERNET BROWSERIntegrated WWW server to ADA-130

5.3.1. NETWORK CONFIGURATIONTo make a changes of default setting or new configuration of ADA-13040MG, select on left panel Configuration -> Network

Fig. 16. Selection serial port profile web5.3.2.1.1. REALPORT (VIRTUAL PORT ) CONFIGURATIONChoosing RealPort (Virtual Port, Fig. 16) is configured the

Fig. 17. Example configuration of TCP serverFor configuration of TCP Client Settings (Fig 18), select Automatically establish TCP connections, connect

5.3.2.1.2.3. SERIAL PORT TRANSMISSION PARAMETERS CONFIGURATIONFor proper operation of ADA-13040MG with device connected to his RS485/RS422 serial por

5.3.2.1.3.2. UDP CLIENT & SERVER CONFIGURATION IN CASE OF SLAVE DEVICESet operating parameters of UDP server for SLAVE device connected via seria

5.3.2.1.3.3. SERIAL PORT TRANSMISSION PARAMETERSFor proper operation of ADA-13040MG with device connected to his RS485/RS422 serial port, should be se

Contents1. GENERAL INFORMATION...

Fig. 22. Example configuration for communication with MODBUS-MASTER devices – choice of devices and protocolsSet the options in section Modbus RTU

Fig. 25. Example configuration for communication with MODBUS-MASTER devices – table entry configuration for SLAVE type devicesOn section Advanced Prot

Fig. 27. Example configuration for communication with MODBUS-SLAVE devices – choice of devices and protocolsSet options in section [Modbus RTU Settin

ATTENTION !Default port of Industrial Automation (Modbus Gateway) service is 502.If on the local network is conflict with other network service using

C/ User Permissions - user permissions to configuration and management of the ADA-13040MG converter, where are an options:None - no permission,Read -

6. USING VIRTUAL PORT SERVICE [REALPORT] 6.1. VIRTUAL PORT DRIVER INSTALLATION IN WINDOWS XPThe installation of virtual serial port drivers should be

Fig. 31. Devices view on Windows XPFig. 32. Example configuration of multi-port serial adapter 26ADA-13040MG

7. FACTORY DEFAULTParameter ValueUser name rootPassword dbpsIP address Obtain an IP address automatically using DHCPOperating mode RealPortBout rate[b

Transmission line4-pair twisted cable, UTP 4x2x0,5 (24AWG), shield inside large interferences STP 4x2x0,5 (24AWG)).1-2-pair twisted cable, eg. UTP 1x2

6. USING VIRTUAL PORT SERVICE [REALPORT] ...

1. GENERAL INFORMATIONThank you for your purchase of CEL-MAR Company product. This product has been completely tested and is covered by two year warra

• Power supply 10 - 30 VDC stable min. 3W,• ~ 3000V= optoizolation in signal channel between ETHERNET and RS485/RS422 interface,• 1000V= or 3000V= gal

2.3.3. COMMUNICATIONS IN THE SERIAL BRIDGE MODECommunication in the serial bridge mode allows to transfer data via Ethernet network between serial por

In the modular socket ETHERNET interface of converter, are implemented two LED's (Fig. 2):– Green ACT signaling state of sending or receiving dat

Fig. 5. The WAN connection to operating in the Real Port mode3.2.3. CONNECTION FOR OPERATING IN TCP & UDP SERIAL BRIDGE MODEFig. 6, 7 below show h

Fig. 7. The LAN connection to operating in the UDP serial bridge mode, one-to-many3.2.4. CONVERTERS CONNECTION AS MODBUS GATEWAYFigure 8 shows connect